Just drop the floatant bottle into this fly fishing accessory and you're ready to go. No need to remove the cap from bottle, insert into caddy and replace cap as with other holders.

Fly fishing floatant accessory is made of light and strong aluminium.

Stormsure Flexible Repair Adhesive is a very strong general purpose adhesive and it can also be used as a surface sealant. It exhibits special characteristics unlike many adhesives as it is highly flexible and stretchy after it has cured but it remains very strong. It fills gaps well, it is suitable for use indoors and outdoors and in marine environments. The adhesive can be painted on top of a surface to make it waterproof, airtight or abrasion resistant. Stormsure adhesive can often be used to cover holes without a patch. A thick film of adhesive will make a good repair. If the glue will drip through the hole just place some sticky tape behind the hole before applying the glue. It can be removed once the glue has cured.

Stormsure Flexible Repair Adhesive bonds to virtually all surfaces including neoprene, rubber, leather, PVC, polyurethane, breathable and coated fabrics, wood, metal and more. It is ideal for repairing cracks in rubber wellington boots, hiking boots, loose soles, leaks in waders, rips in wetsuits, damaged horse rugs, holes in tents and canopies, leaks and splits inflatable items and many other items too. It can also be used for repairs to woodwork and furniture, roof tiles and concrete. 
A tube of Stormsure Flexible Repair Adhesive is an essential part of a repair kit for hikers, DIY, fishermen, equestrians, hunters, divers, campers, surfers, sailors, engineers etc!
Comes with disposable gloves.

DIRECTIONS: Use the adhesive at room temperature. Clean the damaged area to remove dirt and grease (sandpaper the surface for best adhesion). Apply a generous amount of Stormsure Flexible Repair Adhesive to the damaged area, with at least a 5mm extra around the damaged area. Leave horizontal and allow to cure for 10-12 hours.

TIPS: Store partly-used tubes in a deep freezer. Warm up to room temperature before use again.

Stormsure Flexible Repair Adhesive is a very strong general purpose adhesive and it can also be used as a surface sealant. It exhibits special characteristics unlike many adhesives as it is highly flexible and stretchy after it has cured but it remains very strong. It fills gaps well, it is suitable for use indoors and outdoors and in marine environments. The adhesive can be painted on top of a surface to make it waterproof, airtight or abrasion resistant. Stormsure adhesive can often be used to cover holes without a patch. A thick film of adhesive will make a good repair. If the glue will drip through the hole just place some sticky tape behind the hole before applying the glue. It can be removed once the glue has cured.

Stormsure Flexible Repair Adhesive bonds to virtually all surfaces including neoprene, rubber, leather, PVC, polyurethane, breathable and coated fabrics, wood, metal and more. It is ideal for repairing cracks in rubber wellington boots, hiking boots, loose soles, leaks in waders, rips in wetsuits, damaged horse rugs, holes in tents and canopies, leaks and splits inflatable items and many other items too. It can also be used for repairs to woodwork and furniture, roof tiles and concrete. 
A tube of Stormsure Flexible Repair Adhesive is an essential part of a repair kit for hikers, DIY, fishermen, equestrians, hunters, divers, campers, surfers, sailors, engineers etc!
Comes with disposable gloves.

DIRECTIONS: Use the adhesive at room temperature. Clean the damaged area to remove dirt and grease (sandpaper the surface for best adhesion). Apply a generous amount of Stormsure Flexible Repair Adhesive to the damaged area, with at least a 5mm extra around the damaged area. Leave horizontal and allow to cure for 10-12 hours.

TIPS: Store partly-used tubes in a deep freezer. Warm up to room temperature before use again.

Although each bottle of BUG-BOND™ comes with a general purpose tip, many fly tyers like to have the benefit of precise application of the resin.

The Tip-Kit consists of a replacement bottle top that accepts the Luer lock stopper that is included along with 5 pink taper tip applicators.

The taper tips can be stored "wet" in between tying sessions in a small plastic bag, then placed in an envelope and kept in a cool and dark environment until next time.

ATZ's powerful UV Profesional Light is perfect for curing any UV resin for fly tying.

A push button on/off and a powerful beam makes quick work of curing UV resins so you can tie more and fish more.

UV light for curing UV resins 5 Watt output High intensity light for fly tying applications

Uses 1 AA battery (Supplied W/O batteries)

How To Use:

While indoors or shaded from the sun, apply ATZ UV product and form into desired shape. To cure, shine UV ATZ Profesional Light on UV product. UV product should be fully cured and hardened within 10 seconds.

ATZ's Universal UV Cure Light is an excellent light for curing UV resins when tying flies.

This high quality UV light is very powerful, effective and modestly priced, making it a great choice to cure any UV product within a matter of seconds.

• Push button on/off switch
• Requires 3 AAA batteries (not included)

This torch is developed to provide a UV light in range 405nm. Means that this light is in UV Spectrum but in the visible part. For this reason the light color is slightly fluorescent/violet The generator of light is a diode type of laser! Means that the light goes parallel from torch and remain very concentrated in a small round spot. For us is a great way to put a more concentrate light on parts where we applied UV resin and will cure very fast compared with classic torch that have a wide dispersal light angle.

Technical Details:

• Laser 5mW UV type of light 405nm
• Wave range can sures UV resins like Trout Line UV Resins,  Deer Creek UV Resins, Bug-Bond UV Resin, Loon UV Resins...
• Curing time from 1 to 3 seconds depending of how thick is the layer
• Delivered w/o AAA batteries
• Can be used for curing the UV Gel applied on waders to fix small leakes

This Ultra Violet LED is an ingenious micro UV LED light.

UV light for curing UV products

High intensity light for tying and bench applications

This torch has been tested with BugBond and  it works very well at curing it.

• Micro size - goes anywhere you go
• Incredibly bright - visible over one mile!
• Dual function On/Off switch & squeeze button
• Unbreakable LED lamp
• Suitable for dark areas, camping/hunting/hiking and emergency use .
• Battery: 1 x 2PCS CR2016 cell button batteries(built-in )

Almost every fly tyer has a mobile phone or computer handy with USB port. Fed up with purchasing batteries for UV torches or buying mains adapters to ensure continuous power we decided we wanted to have a UV Torch that was USB powered. USB charging means that the torch can simply be plugged into the USB port so that it is always at full charge.

Specifications For Semperfli 3W USB Chargeable UV Torch

• Size: 16x 22x 120mm
• 365nm wavelength
• CREE LED
• Wattage 3 watts power
• Waterproof housing IP65 rated
• Aluminium Alloy Cased
• Battery built in lithium battery recharged by USB port

There are concerns over Picric Acid in the fly fishing industry. Semperfli Picric Acid is laboratory manufactured for us specially and is safe for dying of fly tying feathers, furs and synthetics. We use Picric diluted 100ml (full bottle provided with 2 litres of water.  
 
Picric Acid crystals or 2,4,6-trinitrophenol were dangerous and used for explosives, indeed the navy used this to fire canons pre 1916. It was first mentioned in alchemical writings of Johann Rudolf Glauber in 1742. The picric acid would form very sensitive picric salts within days of filling the shells and would often detonate from the shock of firing. Lacquering the insides of the shells and spraying them with a turpentine/starch solution neutralized the picric acid and prevented it from forming picric salts. Today we use diluted picric acid and store this in plastic containers. We do not use metals even for agitation and it is perfectly safe.  
 
Usage: We use plastic bowls for dilution and use plastic tools to agitate the picric acid. We leave the materials in until they have visibly changed. Some materials like thick wings, grouse for example may take a couple of days for full penetration of the picric acid whereas pheasant tails can dye in 15 minutes to 1 hour. We use latex gloves as picric acid, although not dangerous does make your hand look like you have smoked 60 cigarettes per day for years we have found from accidental spillage when we first started working with the laboratory to manufacture the product. For safety with ALL dying, from picric acid dying to acid dying we use safety glasses and latex gloves.
 
Once the materials have achieved the olive color that you require simply wash off excess picric acid under running water. We then dry the feathers and furs with a drying cabinet (a hairdryer is an alternative!)
 
PROTECTIVE EQUIPMENT - HAND PROTECTION Use protective gloves.  The most suitable glove should be chosen in consultation with the gloves supplier, who can inform about the breakthrough time of the glove material.
 
EYE PROTECTION Wear approved, tight-fitting safety glasses where splashing is probable.
 
RESPIRATORY EQUIPMENT Self-contained breathing apparatus where high splashing is likely.
 
OTHER PROTECTION Provide eyewash station.
 
HYGIENE MEASURES DO NOT SMOKE IN WORK AREA! Wash at the end of each work shift and before eating, smoking and using the toilet.  Promptly remove any clothing that becomes contaminated. Wash promptly with soap & water if skin becomes contaminated.
 

Package Contents:

• 100ml Picric Acid Solution
• Full Safety Data Sheet
• Safety Gloves

You Will Need:

• Plastic Bowl
• Safety Glasses
• Water
• Plastic Utensil (for removing from dye bath and washing)
• Safe drying space

Neoprene Queen Adhesive is a fast-curing, thick, black glue. Its premium quality and properties make it perfect for repairing wetsuit and drysuit damage that regularly occurs over time with regular use. This nifty adhesive will enable you to make easy and durable repairs to rips, roles, leaks and split seams on wetsuit and drysuit material. 

To use, apply to both edges of a rip and bond firmly together for 20 seconds. Within 5 minutes, it should be touch dry and you will be ready to go back in the water!

An essential tool for divers, anglers, surfers, body boarders, kite surfers and sailors.

Perfect for casual water sports enthusiasts as well as professional triathletes who want to stand out.

Use for maintaining latex seals in good condition, and lubricating drysuit zips.